How do I set the timer on my hunter sprinkler system

Step 1: Set The Current Time. First, you will want to ensure that the current time is correct. … Step 2: Set the Start Times. Next, turn the dial to “Start Times”. … Step 3: Set the Run Time. … Step 4: Set the Watering Days. … Step 5: Test Coverage. … Step 6: Finished!

How do you program a hunter sprinkler timer?

Step 1: Set The Current Time. First, you will want to ensure that the current time is correct. …
Step 2: Set the Start Times. Next, turn the dial to “Start Times”. …
Step 3: Set the Run Time. …
Step 4: Set the Watering Days. …
Step 5: Test Coverage. …
Step 6: Finished!

How do you set water days on Hunter Pro C?

To set EVEN days to water, press the (RIGHT ARROW) button until the ODD flashes, then press the button once. You will see a icon flashing above “ODD”. This indicates an interval of 1 day with NO ODD Day watering. The controller will water every EVEN day.

How do I reset my Hunter EC Controller?

Press and hold down the , and buttons.
Press and release the RESET button in the lower wiring compartment.
Wait 2 seconds and release the , and buttons. The display should now show 12:00a. m.
All the memory has been cleared and the controller may now be reprogrammed.

How do I reset my Hunter SRC Plus sprinkler?

Press and hold down the , and buttons.
Press and release the RESET button in the lower wiring compartment.
Release the , and buttons. The display should now show 12:00a. m.
All the memory has been cleared and the controller may now be reprogrammed.

How do I reset my orbit sprinkler timer?

To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. …
Reset to Factory Default – Orbit Irrigation B-hyve Help. …
Remove battery, remove power, do the wifi reset per the instructions (reset button on rear of swing out panel) remove app from your phone – should do it.

Where is the reset button on a Hunter thermostat?

Press and release the RESET button on the back of the front panel.

Why is my sprinkler system not turning off?

It is possible that the sprinkler valves need a good cleaning since dirt and debris can get trapped in the valve and cause problems. So, for a little DIY practice, check to see if the valves are clogged. If the valves are clean, check to see if they are cracked or broken.

How do I reset my hunter X2 sprinkler?

Turn the dial to the RUN position. …
Press and hold the program button.
Press and release the RESET button located inside the lower wiring compartment. …
When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

How do you turn off interval watering on Hunter Pro C?

Under the Water Days or Days to Water dial position on your controller you have three options. You can have the program run on specific days, an odd/even schedule, or an interval schedule. To move out of the Interval mode and back into one of your other two options simply continue pressing the or buttons.

Article first time published on

What are even and odd watering days?

Under the odd/even watering schedule, houses with addresses ending with an odd number water on odd-numbered days; houses ending with an even address water on even-numbered days. This alternating watering schedule significantly reduces the peak effect of everyone wanting to water at the same time.

What is Hunter SRC Plus?

9. The Hunter SRC Plus is remote-ready for use with the SRR or ICR remote control system. The remote makes it possible for contractors and end-users alike to operate an system without having to walk back and forth to the controller.

What is RS on Hunter SRC Plus?

The function of RS terminal was to notify the controller the status of the rain sensor. Rachio uses a different approach, Commons are dedicated to valves and rain sensor can be connected to the dedicated inputs.

How do I reset my sprinkler system?

Turn the control dial to the “off” position.
Press the “next” button to access the clear-memory feature. …
Press and hold the “off” button until the display stops blinking.
Turn the control dial to the “run” position.
Press and hold down the “minus” arrow and “prog” buttons simultaneously.

How do you use a hunter touchscreen thermostat?

Touch the screen while it is in sleep/ready mode to turn on the Hunter thermostat. …
Tap the day that you want to set a program for on the screen. …
Touch the “Heat” or “Cool” icon to select the system you want to engage.

What does a flashing 3 mean on a Hunter thermostat?

A flashing 3 means the third setting is currently operating the heater or AC.

What does em mean on Hunter thermostat?

Short for “emergency heat,” it is a setting that controls your home’s back-up heating system. If you have an emergency heat thermostat setting, you likely have a heat pump, as well as a gas, oil, electric, or hot-water back-up system.

Should solenoid be on or off?

Avoid over-turning the solenoid in either direction, as this can cause damage to the components or cause pressurised water to escape the solenoid. When you hear water rush through the device, it’s easy to tell that the valve has opened successfully.

Is there an app for Hunter sprinkler system?

Hunter Hydrawise Remote access is possible through either the Hydrawise app (iOS or Android compatible devices) or online through their cloud software. Key product features include: Predictive Watering Adjustments based on web-based weather data brings up to 50 percent in water savings.

How do I set the time on my hunter node timer?

To set the time and date on the node press the center button, simply scroll through the choices using the left and right arrow buttons and adjust the displayed item using the plus and minus buttons. Push the button until the icon is displayed. All 4 digits will be displayed representing the year.

How do you program a orbit 6 sprinkler timer?

Turn the dial to “Cycle Start Times.”
Press the “+” or “-” to set the start time.
Press “Enter” to confirm the start time.
Press “Next” to set the start time for each additional program, following the same procedure.