The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
How far should a toilet be from the back wall?
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.
What is rough in distance for toilet?
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. … Rear-outlet toilets are configured a bit differently.
How do you measure a toilet setback?
Measure from the wall behind the toilet to the center of one of the closet bolts (which hold the toilet down). If the toilet has four closet bolts, measure to the center of one of the rear ones. Then measure from the center of the mounting holes to the back of the new toilet you’re considering.How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
Can I move a toilet a few inches?
Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line and in turn help to save you a lot of money.
Why is my new toilet so far from the wall?
When toilet flanges are installed it is typically in the early stages of the project and the standard 12” measurement is taken from the drywall, rather than the finished tile surface that you are measuring from. That means your flange was set at a distance further from the wall than even the 13″ you measured.
Do all toilets fit the same?
For a standard toilet, the rough-in measurement should be between 11 inches and 13 inches. … If the rough-in measurement is not between 11 inches and 13 inches, a standard toilet will not fit the space, and you will need to look for a toilet designed for that specific rough-in distance.How much space do you need around a toilet?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
Can you replace a 10 inch rough-in toilet with a 12-inch rough-in toilet?The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
Article first time published onWhat is the difference between a 12 and 14 rough-in toilet?
The main difference between 12-inch rough-ins and 14-inch rough-ins is in their size (proportions). Depending on the type of bathroom, 12-inch rough-ins are generally more used than 14-inch rough-ins, but they both have merits, which means that you sometimes need to reduce the space from behind the tank.
Where should a toilet flange be placed?
When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits even or below the floor, then it’s wrong. It has to sit evenly on top of the finished floor. This is very important.
Why would I want an elongated toilet bowl?
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
What is a compact toilet?
Essentially, a compact toilet simply takes up less space. This is done by giving it a smaller water tank or seat or opting for a round bowl instead of an elongated one. … Some compact toilets measure just 15 inches wide, although other compact models can be significantly wider.
What is an offset flange?
Unlike a standard flange, which is centered on the waste pipe, an offset flange is off-center—that lets you shift the location of the toilet by a couple of inches (left, right, forward or back).
Can you move a toilet closer to the wall?
While the 12 inches from the back wall to the center of the toilet remains standard, the recommended distance from the center of the toilet flange to side walls is 18 inches and 30-36 inches from the front of the toilet to the opposite wall or fixture.
Does a toilet have to be against a wall?
Toilets should have a minimum of 15 inches from walls that flank the fixture. A distance of 12 to 12.5 inches should be between the center of the toilet flange and the back wall.
How many inches does an offset toilet flange move?
The typical offset is 12-inches for most residential toilets.
How far does an offset toilet flange move the toilet?
For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.
How close can a toilet be to a bathtub?
It is recommended that the distance from the centerline of a toilet and/or bidet to any bath fixture, wall, or other obstacle should be at least 18 inches. The minimum distance from the centerline of a toilet and/or bidet to any bath fixture, wall, or other obstacle is 15 inches.
Why is the toilet always next to the shower?
Toilets tend to be next to bathtubs because both of them tend to be in a small room that is kept rather private from the rest of the house and because both of them need to have fairly substantial plumbing in order to operate correctly.
How much room do you need for a toilet and sink?
Each has a minimum space allowance to pass code. A toilet requires a minimum 30 inches of space to sit in by itself: 15 inches from the center line out to each side. Sinks require a minimum of 20 inches of space to sit in, if they are the only sink in the room.
How much clearance do you need for a toilet Canada?
Toilets should have at least 15 inches clearance to side obstructions such as walls, tubs and showers. Measurement is from the center of the toilet. Toilets and sinks should have at least 21 inches (more in some jurisdictions) clearance in front.
What is the footprint of a toilet?
A toilet “footprint” is basically the measurement or size of where the bottom of the toilet pedestal meets the floor.
How do you measure toilet depth?
To measure the depth of your current toilet, measure from the front edge of the toilet bowl to the back of the tank. If you are comfortable with your current toilet’s depth, then select a new toilet with a similar depth.
Can an elongated toilet replace a round toilet?
An elongated toilet seat will technically fit on a round toilet, but the fit and comfort may be compromised. An elongated toilet seat will likely overhang a round toilet which may be fine unless the rim of the toilet is visible within the opening of the toilet seat.
Are most toilets 10 or 12 rough-in?
A 10-inch rough-in is the usual measurement installed in older homes. However, the 12-inch measurement is the standard for modern toilet plumbing. Most toilets that you encounter in retail outlets have 12-inch rough-in dimensions.
How do I know which toilet to buy?
- To determine the size of your toilet rough-in, measure from the wall behind the toilet to the bolt caps of your current toilet. …
- Most toilets are available in a 12-inch rough-in, which is the standard distance, but a 10- or 14-inch rough-in may be needed in some homes.
How do you measure a rough-in corner for a toilet?
To determine the toilet rough-in location, measure and mark the rough-in length out from the corner on each wall. For this example, a toilet with a 12″ rough-in was used. 2. Use a straight edge to draw two perpendicular lines from the marks created in the previous step.
Can you put a 12 inch rough in toilet on a 14 inch rough in?
Most toilets that advertise as a 14″, install using a 12“ bowl. This leaves the bowl pretty far out into the room. TOTO at least gives you the option to shift the bowl back closer to the wall. And yes, they work great!
Does the toilet flange sit on top of tile?
5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.
